CSA American INSERT-30-4026 Manual de instalación

1 malfunction and result in serious injury and/or property damage. WARNING: All electric heaters have hot or sparking parts inside. Do

NOTE: This appliance must be electricallywired and grounded in accordance withlocal codes. In the absence oflocal codes,us the current CSA C22.1 Canadi

NOTE: This appliance must be electricallywired and grounded in accordance withlocal codes. In the absence oflocal codes,us the current CSA C22.1 Canadi

NOTE: This appliance must be electricallywired and grounded in accordance withlocal codes. In the absence oflocal codes,us the current CSA C22.1 Canadi

NOTE: This appliance must be electricallywired and grounded in accordance withlocal codes. In the absence oflocal codes,us the current CSA C22.1 Canadi

LOCATING THE FIREPLACE INSERT Heater must be placed so it remains level (use included level to verify). Leveling bolts are provided on the bas

CLEARANCES WHEN BUILT-IN UNPACKING AND TESTING THE FIREPLACE INSERT Carefully remove the fireplace insert from the box. Remove the packing screws

INSTALLATION CAUTION: The unit's power supply cord must be connected to a properly grounded and protected 120-volt outlet. Always use

INSTALLATION OVERVIEW – MASONRY FIREPLACES 2” (50mm) MinimumHINT:Paint the interior of the fireplace with latex paint to prevent fireplace odors from

INSTALLATION OVERVIEW – ZERO-CLEARANCE (METAL) FIREPLACES 2” (50mm) MinimumThe log shelf, screen, and doors (if present) must be removed.HINT:Paint t

OPTIONAL DECORATIVE INTERIORS This insert is shipped with an under-lit log pre-installed. Glowing embers are also included with the fireplace inse

2 Keep this manual for future reference. SAFETY INFORMATION When using electrical heaters, basic precautions, like the ones listed

OPERATING INSTRUCTIONS REMOVING THE SURROUND GLASS Before removing the surround glass, make sure to have a suitable location to place the surround gl

21REMOTE CONTROL OPERATION The button located at the top position of the remote control is ON/OFF. Press it, the flame and ember will be on. The heat

REMOTE CONTROL OPERATION 22The button located at the top position of the remote control is ON/OFF. Press it, the flame and ember will be on. The heat

DIRECT OPERATION 1. Power ON/OFF switch 2. Heat control button 3. Flame control button 4. HEATER LED 5. POWER LED Plug the heater into a

CLEANING AND MAINTENANCE FRONT GLASS 1. Remove dust by buffing lightly with a clean dry cloth. 2. To remove fingerprints or other marks, the

TROUBLE SHOOTING OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Fireplace insert turns off and will not turn on Fireplace insert has overheated

REF NO.PART NO. DESCRIPTION REMAKR1602030C BLOWER AND HEATER ASSEMBLYFRT604202601086C CIRCUIT BOARD LRC8-032601089E CIRCUIT BOARD LRC9-053301506 REMOT

SERVICE HISTORY27

Defects must be brought to the atenton of Amanti Technical Service by contactng Amanti at (1-888-406-8764), or at 502-1207This limited warranty do

3 12. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to

4 NOTE: This appliance must be electricallywired and grounded in accordance withlocal codes. In the absence oflocal codes,us the current CSA C22.1 Can

5 NOTE: This appliance must be electricallywired and grounded in accordance withlocal codes. In the absence oflocal codes,us the current CSA C22.1 Can

NOTE: This appliance must be electricallywired and grounded in accordance withlocal codes. In the absence oflocal codes,us the current CSA C22.1 Canadi

NOTE: This appliance must be electricallywired and grounded in accordance withlocal codes. In the absence oflocal codes,us the current CSA C22.1 Canadi

NOTE: This appliance must be electricallywired and grounded in accordance withlocal codes. In the absence oflocal codes,us the current CSA C22.1 Canadi

NOTE: This appliance must be electricallywired and grounded in accordance withlocal codes. In the absence oflocal codes,us the current CSA C22.1 Canadi